Default Hardware
CPU
- Freescale Inc. mpc8347 sys
- e300 266 MHz core / 266 MHz bus
- 177.15 bogomips
PCI
- eth0: Realtek RTL8211B (10/100/1000Mbps Ethernet)
- eth1: Marvell 88E6060 (Commercial Grade 6-Port Fast Ethernet Switch)
- PCI ID: 1095:3512 Sil 3512 SATA Controller by Silicon Image
Other
- 128MB memory
- Freescale MPC8349MDS flash (8MB?) used, where kernel stored, as a MTD in Linux
- Kernel boot command:
root=/dev/ram init=/linuxrc rw console=ttyS0,115200 ramdisk_size=32768
dmesg output
Linux version 2.6.11.12 (root@dev_222) (gcc version 3.4.3) #3 Wed Apr 18 11:38:42 CST 2007
On node 0 totalpages: 32768
DMA zone: 32768 pages, LIFO batch:8
Normal zone: 0 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=/dev/ram init=/linuxrc rw console=ttyS0,115200 ramdisk_size=32768
IPIC (128 IRQ sources, 8 External IRQs) at fe000700
PID hash table entries: 1024 (order: 10, 16384 bytes)
Console: colour dummy device 80x25
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 122272k available (2200k kernel code, 616k data, 104k init, 0k highmem)
Calibrating delay loop... 177.15 BogoMIPS (lpj=88576)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 4425k freed
NET: Registered protocol family 16
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 0 of device 0000:00:00.0
PCI: Cannot allocate resource region 2 of device 0000:00:00.0
PCI: Failed to allocate mem resource #2:80000000@0 for 0000:00:00.0
Registering ipic with sysfs...
SCSI subsystem initialized
NTFS driver 2.1.22 [Flags: R/O].
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
ttyS0 at MMIO 0xe0004500 (irq = 9) is a 16550A
ttyS1 at MMIO 0xe0004600 (irq = 10) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
eth0: Gianfar Ethernet Controller Version 1.4, 00:14:fd:10:99:6c
eth0: MTU = 1500 (frame size=1514,truesize=1800)
eth0: Running with NAPI enabled
eth0: 64/64 RX/TX BD ring size
eth0: Socket buffer recycling mode enabled
eth1: Gianfar Ethernet Controller Version 1.4, 00:14:fd:10:99:6d
eth1: MTU = 1500 (frame size=1514,truesize=1800)
eth1: Running with NAPI enabled
eth1: 64/64 RX/TX BD ring size
eth1: Socket buffer recycling mode enabled
SKB Handler initialized(max=64)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu>
libata version 1.10 loaded.
sata_sil version 0.9
sata_sil(0000:00:10.0): cache line size not set. Driver may not function
sata_silApplying R_ERR on DMA activate FIS errata fix
ata1: SATA max UDMA/100 cmd 0xC9050E80 ctl 0xC9050E8A bmdma 0xC9050E00 irq 20
ata2: SATA max UDMA/100 cmd 0xC9050EC0 ctl 0xC9050ECA bmdma 0xC9050E08 irq 20
ata1: dev 0 cfg 49:2f00 82:746b 83:7f61 84:4163 85:7469 86:be41 87:4163 88:007f
ata1: dev 0 ATA, max UDMA/133, 976773168 sectors: lba48
ata1: dev 0 configured for UDMA/100
scsi0 : sata_sil
ata2: no device found (phy stat 00000000)
scsi1 : sata_sil
Vendor: ATA Model: WDC WD5000ABYS-0 Rev: 12.0
Type: Direct-Access ANSI SCSI revision: 05
Thecus Tray: 1, sda
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
MPC8349MDS flash device: 800000 at fe000000 Partition number 5
MPC8349MDS Flash Map Info: Found 1 x16 devices at 0x0 in 16-bit bank
Intel/Sharp Extended Query Table at 0x0031
Using buffer write method
cfi_cmdset_0001: Erase suspend on write enabled
0: offset=0x0,size=0x20000,blocks=64
Creating 5 MTD partitions on "MPC8349MDS Flash Map Info":
0x00000000-0x00040000 : "u-boot"
0x00040000-0x00080000 : "u-boot config"
0x00080000-0x00180000 : "user"
0x00180000-0x00320000 : "kernel"
0x00320000-0x00800000 : "ramdisk"
MPC8349MDS flash device initialized
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
Attaching PIC16F72
md: raid1 personality registered as nr 3
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 5
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sda1 ...
md: adding sda1 ...
md: sda2 has different UUID to sda1
md: created md1
md: bind<sda1>
md: running: <sda1>
raid1: raid set md1 active with 1 out of 2 mirrors
md: considering sda2 ...
md: adding sda2 ...
md: created md0
md: bind<sda2>
md: running: <sda2>
raid1: raid set md0 active with 1 out of 2 mirrors
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 104k init
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
cloop: Initializing cloop v2.01
cloop: loaded (max 8 devices)
cloop: losetup_file: 129 blocks, 65536 bytes/block, largest block is 61669 bytes.
cloop: losetup_file: 65 blocks, 65536 bytes/block, largest block is 19920 bytes.
cloop: losetup_file: 469 blocks, 65536 bytes/block, largest block is 59487 bytes.
Attaching F75375
eth0: PHY is Realtek RTL8211B (1cc912)
eth0: Full Duplex
eth0: Speed 100BT
eth0: Link is up
eth1: PHY is Marvell 88E6060 (1410c87)
ReiserFS: md0: found reiserfs format "3.6" with standard journal
ReiserFS: md0: using writeback data mode
ReiserFS: md0: journal params: device md0, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md0: checking transaction log (md0)
ReiserFS: md0: replayed 2 transactions in 0 seconds
ReiserFS: md0: Using r5 hash to sort names
usbcore: registered new driver hub
driver fsl-usb2-mph, $Revision: 1.11 $
fsl-usb2-mph fsl-usb2-mph1: new USB bus registered, assigned bus number 1
fsl-usb2-mph fsl-usb2-mph1: park 0
fsl-usb2-mph fsl-usb2-mph1: USB 0.0 initialized, EHCI 1.00, driver $Revision: 1.11 $
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
zd1211 - http://zd1211.ath.cx/ - r83
Based on www.zydas.com.tw driver version 2.5.0.0
usbcore: registered new driver zd1211
ZD1211B - http://zd1211.ath.cx/ - r83
Based on www.zydas.com.tw driver version 2.5.0.0
Adding 1003896k swap on /dev/md1. Priority:-1 extents:1
usbcore: registered new driver zd1211b
