Thecus N3200PRO Hardware

From NAS Website

Default Hardware for N3200PRO/M3800

CPU

AMD geode LX800 500Mhz

This is the contents of /proc/cpuinfo:

processor   : 0
vendor_id   : AuthenticAMD
cpu family  : 5
model       : 10
model name  : Geode(TM) Integrated Processor by AMD PCS
stepping    : 2
cpu MHz     : 498.068
cache size  : 128 KB
fdiv_bug    : no
hlt_bug     : no
f00f_bug    : no
coma_bug    : no
fpu     : yes
fpu_exception   : yes
cpuid level : 1
wp      : yes
flags       : fpu de pse tsc msr cx8 pge cmov clflush mmx mmxext 3dnowext 3dnow
bogomips    : 997.48
clflush size    : 32

RAM

256MiB DDR400 SO-DIMM
http://www.poolshark.org/thecus/img/M3800_RAM.jpg

PSU

FSP096-AHB
AC Input: 100-240V~2A, 50~60HZ
DC Output: 12V==8A

Onboard storage

128MB flash microdisk with 2.5" 44 pin IDE Connector
Manufacturer is shown as Afaya (AFAYA MDM 128M)
Part number on mine is MDM4SLOS064MBPC.
Link to manufacturers information for this part: AFAYA Products page (http://www.afaya.com.tw/afaya-01/htm/products/01_mdm_l.htm)
This is a "left" side module. A vertical module will not fit as it extends vertically from the motherboard and would hit the case. A right hand module would face towards the bottom of the unit and may not fit because of interference with the base of the unit.
http://www.poolshark.org/thecus/img/M3800_MDM1.jpg
http://www.poolshark.org/thecus/img/M3800_MDM2.jpg

Disk Backplane

3-Slot SATA disk backplane perpendicular to the CPU board, with a N3200 printed label
SATA Controller is an on-board SiI 3114, a 4-port SATA150 PCI controller (Product page)
http://www.poolshark.org/thecus/img/M3800_SiI3114.jpg

PCI

This is the output of lspci:

00:01.0 Host bridge: Advanced Micro Devices [AMD] CS5536 [Geode companion] Host Bridge (rev 33)
	Flags: bus master, 66MHz, medium devsel, latency 248
	I/O ports at ac1c [size=4]

00:01.1 VGA compatible controller: Advanced Micro Devices [AMD] Geode LX Video (prog-if 00 [VGA controller])
	Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 7
	Memory at ee000000 (32-bit, non-prefetchable) [size=16M]
	Memory at efff0000 (32-bit, non-prefetchable) [size=16K]
	Memory at effec000 (32-bit, non-prefetchable) [size=16K]
	Memory at effe8000 (32-bit, non-prefetchable) [size=16K]
	Memory at efff8000 (32-bit, non-prefetchable) [size=16K]

00:01.2 Entertainment encryption device: Advanced Micro Devices [AMD] Geode LX AES Security Block
	Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 7
	Memory at efff4000 (32-bit, non-prefetchable) [size=16K]

00:0b.0 Multimedia controller: Sigma Designs, Inc. Unknown device c623 (rev 82)
	Subsystem: Sigma Designs, Inc. Unknown device 0000
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 5
	Memory at ed000000 (32-bit, non-prefetchable) [size=16M]
	Capabilities: [40] Power Management version 1

00:0c.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet Controller (rev 05)
	Subsystem: Intel Corporation PRO/1000 MT Network Connection
	Flags: bus master, 66MHz, medium devsel, latency 252, IRQ 5
	Memory at effa0000 (32-bit, non-prefetchable) [size=128K]
	I/O ports at ff00 [size=64]
	Capabilities: [dc] Power Management version 2
	Capabilities: [e4] PCI-X non-bridge device

00:0d.0 Ethernet controller: Intel Corporation 82541GI Gigabit Ethernet Controller (rev 05)
	Subsystem: Intel Corporation PRO/1000 MT Network Connection
	Flags: bus master, 66MHz, medium devsel, latency 252, IRQ 10
	Memory at effc0000 (32-bit, non-prefetchable) [size=128K]
	I/O ports at fe00 [size=64]
	Capabilities: [dc] Power Management version 2
	Capabilities: [e4] PCI-X non-bridge device

00:0e.0 Mass storage controller: Silicon Image, Inc. SiI 3114 [SATALink/SATARaid] Serial ATA Controller (rev 02)
	Subsystem: Silicon Image, Inc. SiI 3114 SATALink Controller
	Flags: bus master, 66MHz, medium devsel, latency 64, IRQ 11
	I/O ports at fd00 [size=8]
	I/O ports at fc00 [size=4]
	I/O ports at fb00 [size=8]
	I/O ports at fa00 [size=4]
	I/O ports at f900 [size=16]
	Memory at effff000 (32-bit, non-prefetchable) [size=1K]
	[virtual] Expansion ROM at 10000000 [disabled] [size=512K]
	Capabilities: [60] Power Management version 2

00:0f.0 ISA bridge: Advanced Micro Devices [AMD] CS5536 [Geode companion] ISA (rev 03)
	Flags: 66MHz, medium devsel
	I/O ports at 6000 [size=8]
	I/O ports at 6100 [size=256]
	I/O ports at 6200 [size=64]
	I/O ports at 1000 [size=32]
	I/O ports at 9d00 [size=128]
	I/O ports at 9c00 [size=64]

00:0f.2 IDE interface: Advanced Micro Devices [AMD] CS5536 [Geode companion] IDE (rev 01) (prog-if 80 [Master])
	Flags: bus master, 66MHz, medium devsel, latency 248
	[virtual] Memory at 000001f0 (32-bit, non-prefetchable) [disabled] [size=8]
	[virtual] Memory at 000003f0 (type 3, non-prefetchable) [disabled] [size=1]
	[virtual] Memory at 00000170 (32-bit, non-prefetchable) [disabled] [size=8]
	[virtual] Memory at 00000370 (type 3, non-prefetchable) [disabled] [size=1]
	I/O ports at f800 [size=16]

00:0f.4 USB Controller: Advanced Micro Devices [AMD] CS5536 [Geode companion] OHC (rev 02) (prog-if 10 [OHCI])
	Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 10
	Memory at efffe000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [40] Power Management version 2

00:0f.5 USB Controller: Advanced Micro Devices [AMD] CS5536 [Geode companion] EHC (rev 02) (prog-if 20 [EHCI])
	Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 10
	Memory at efffd000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [40] Power Management version 2

Video (VGA output)

The case has no visible VGA output, but the motherboard has an IDC-10 connector (to the left of the CPU) that connects to the on-chip VGA controller of the AMD Geode CPU. A custom cable is required to use it.

HDMI Video (M3800 only)

An imposing-looking video card is inserted in the CPU board slot. The card appears to be made by multimedia specialist Sigma Designs, Inc and is labelled as "SD862X". The card has 4 outputs, including an HDMI port and a S/PDIF digital audio output.
The video card GPU is a Sigma Designs EM8623L-LF
http://www.poolshark.org/thecus/img/M3800_sigma.jpg

External ports

eSATA connector
USB 2.0 ports (1x back, 1x front)
WAN 1000 Mbps Ethernet connector (Intel 82541 PI)
LAN 1000 Mbps Ethernet connector (Intel 82541 PI)

Internal ports

I2C Port for LCD display
VGA Port (IDC-10 connector)

dmesg

This is the contents of dmesg (for the N3200PRO) :

Linux version 2.6.23 (root@RD224.thecus.com) (gcc version 4.1.2 20070925 (Red Hat 4.1.2-33)) #1 Fri Sep 19 14:42:50 CST 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009e800 (usable)
 BIOS-e820: 000000000009e800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000000f7b0000 (usable)
 BIOS-e820: 000000000f7b0000 - 000000000f7b3000 (ACPI NVS)
 BIOS-e820: 000000000f7b3000 - 000000000f7c0000 (ACPI data)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
247MB LOWMEM available.
Using x86 segment limits to approximate NX protection
Entering add_active_range(0, 0, 63408) 0 entries of 256 used
Zone PFN ranges:
  DMA             0 ->     4096
  Normal       4096 ->    63408
  HighMem     63408 ->    63408
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0:        0 ->    63408
On node 0 totalpages: 63408
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 463 pages used for memmap
  Normal zone: 58849 pages, LIFO batch:15
  HighMem zone: 0 pages used for memmap
  Movable zone: 0 pages used for memmap
DMI 2.2 present.
ACPI: RSDP 000F5E50, 0014 (r0 AMDGX3)
ACPI: RSDT 0F7B3000, 0028 (r1 AMDGX3 AWRDACPI 42302E31 AWRD        0)
ACPI: FACP 0F7B3080, 0074 (r1 AMDGX3 AWRDACPI 42302E31 AWRD        0)
ACPI: DSDT 0F7B3100, 2C30 (r1 AMDGX3 AWRDACPI     1000 MSFT  3000000)
ACPI: FACS 0F7B0000, 0040
ACPI: PM-Timer IO Port: 0x9c10
Allocating PCI resources starting at 10000000 (gap: 0f7c0000:f0830000)
Built 1 zonelists in Zone order.  Total pages: 62913
Kernel command line: ro root=/dev/ram0 max_loop=210 elevator=as acpi=noirq
Initializing CPU#0
PID hash table entries: 1024 (order: 10, 4096 bytes)
Detected 498.064 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 240144k/253632k available (2157k kernel code, 12968k reserved, 805k data, 168k init, 0k highmem)
virtual kernel memory layout:
    fixmap  : 0xfffe9000 - 0xfffff000   (  88 kB)
    pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
    vmalloc : 0xd0000000 - 0xff7fe000   ( 759 MB)
    lowmem  : 0xc0000000 - 0xcf7b0000   ( 247 MB)
      .init : 0xc03e8000 - 0xc0412000   ( 168 kB)
      .data : 0xc031b785 - 0xc03e4f44   ( 805 kB)
      .text : 0xc0100000 - 0xc031b785   (2157 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=22, HWalign=32, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 997.48 BogoMIPS (lpj=1661583)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0088a93d c0c0a13d 00000000 00000000 00000000 00000000 00000000 00000000
AMD LX800 Revision (0x33)
AMD LX800 Revision C3
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 128K (32 bytes/line)
CPU: After all inits, caps: 0088a13d c0c0a13d 00000000 00000000 00000000 00000000 00000000 00000000
Compat vDSO mapped to ffffe000.
CPU: AMD Geode(TM) Integrated Processor by AMD PCS stepping 02
Checking 'hlt' instruction... OK.
ACPI: Core revision 20070126
ACPI: setting ELCR to 0ea0 (from 0ca0)
xor: measuring software checksum speed
   8regs     :   394.800 MB/sec
   8regs_prefetch:   333.600 MB/sec
   32regs    :   244.800 MB/sec
   32regs_prefetch:   219.600 MB/sec
   pII_mmx   :   872.400 MB/sec
   p5_mmx    :   682.800 MB/sec
xor: using function: pII_mmx (872.400 MB/sec)
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfaaf0, last bus=0
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S5)
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 10 devices
ACPI: ACPI bus type pnp unregistered
SCSI subsystem initialized
libata version 2.21 loaded.
PCI: Probing PCI hardware
ACPI: RTC can wake from S4
Time: tsc clocksource has been installed.
pnp: 00:00: iomem range 0xf0000-0xfffff could not be reserved
pnp: 00:00: iomem range 0xf7b0000-0xf7bffff could not be reserved
pnp: 00:00: iomem range 0xffff0000-0xffffffff could not be reserved
pnp: 00:00: iomem range 0x0-0x9ffff could not be reserved
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 7279k freed
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
SGI XFS with ACLs, large block numbers, no debug enabled
async_tx: api initialized (async)
io scheduler noop registered
io scheduler anticipatory registered (default)
Boot video device is 0000:00:01.1
lxfb 0000:00:01.1: 8192 KB of video memory at 0xee000000
Console: switching to colour frame buffer device 80x30
fb0: Geode LX frame buffer device
AMD Geode RNG detected
Serial: 8250/16550 driver $Revision: 1.90 $ 1 ports, IRQ sharing disabled
RAMDISK driver initialized: 2 RAM disks of 32768K size 1024 blocksize
loop: module loaded
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2-NAPI
Copyright (c) 1999-2006 Intel Corporation.
e1000: 0000:00:0c.0: e1000_probe: (PCI:66MHz:32-bit) 00:14:fd:12:0a:4c
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
e1000: 0000:00:0d.0: e1000_probe: (PCI:66MHz:32-bit) 00:14:fd:12:0a:4d
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
Linux video capture interface: v2.00
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AMD5536: IDE controller at PCI slot 0000:00:0f.2
AMD5536: chipset revision 1
AMD5536: not 100% native mode: will probe irqs later
AMD5536: ide bus clock: 33
AMD5536: 0000:00:0f.2 (rev 01) UDMA100 controller
    ide0: BM-DMA at 0xf800-0xf807, BIOS settings: hda:pio, hdb:pio
Probing IDE interface ide0...
hda: AFAYA MDM 128M, ATA DISK drive
hda: selected mode 0x0
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hda: max request size: 128KiB
hda: 250368 sectors (128 MB) w/2KiB Cache, CHS=978/8/32
 hda: hda1 hda2 hda3 hda4
sata_sil 0000:00:0e.0: version 2.3
sata_sil 0000:00:0e.0: Applying R_ERR on DMA activate FIS errata fix
PCI: Setting latency timer of device 0000:00:0e.0 to 64
scsi0 : sata_sil
scsi1 : sata_sil
scsi2 : sata_sil
scsi3 : sata_sil
ata1: SATA max UDMA/100 cmd 0xd0016080 ctl 0xd001608a bmdma 0xd0016000 irq 11
ata2: SATA max UDMA/100 cmd 0xd00160c0 ctl 0xd00160ca bmdma 0xd0016008 irq 11
ata3: SATA max UDMA/100 cmd 0xd0016280 ctl 0xd001628a bmdma 0xd0016200 irq 11
ata4: SATA max UDMA/100 cmd 0xd00162c0 ctl 0xd00162ca bmdma 0xd0016208 irq 11
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata1.00: ATA-8: ST3500320NS, SN05, max UDMA/133
ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/100
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata2.00: ATA-8: ST3500320NS, SN05, max UDMA/133
ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/100
ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata3.00: ATA-8: ST3500320NS, SN05, max UDMA/133
ata3.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/100
ata4: SATA link down (SStatus 0 SControl 310)
scsi 0:0:0:0: Direct-Access     ATA      ST3500320NS      SN05 PQ: 0 ANSI: 5
Thecus Tray: 3, sdc
sd 0:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sdc] THECUS  real size: sdp->tray_id: 3, dkp->capacity: 976773168, sector_size: 512
sd 0:0:0:0: [sdc] THECUS align 128M: sdp->tray_id: 3, dkp->capacity: 976748544, sector_size: 512
sd 0:0:0:0: [sdc] Write Protect is off
sd 0:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sdc] 976773168 512-byte hardware sectors (500108 MB)
sd 0:0:0:0: [sdc] THECUS  real size: sdp->tray_id: 3, dkp->capacity: 976773168, sector_size: 512
sd 0:0:0:0: [sdc] THECUS align 128M: sdp->tray_id: 3, dkp->capacity: 976748544, sector_size: 512
sd 0:0:0:0: [sdc] Write Protect is off
sd 0:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdc: sdc1 sdc2 sdc3
sd 0:0:0:0: [sdc] Attached SCSI disk
scsi 1:0:0:0: Direct-Access     ATA      ST3500320NS      SN05 PQ: 0 ANSI: 5
Thecus Tray: 2, sdb
sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 1:0:0:0: [sdb] THECUS  real size: sdp->tray_id: 2, dkp->capacity: 976773168, sector_size: 512
sd 1:0:0:0: [sdb] THECUS align 128M: sdp->tray_id: 2, dkp->capacity: 976748544, sector_size: 512
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 1:0:0:0: [sdb] 976773168 512-byte hardware sectors (500108 MB)
sd 1:0:0:0: [sdb] THECUS  real size: sdp->tray_id: 2, dkp->capacity: 976773168, sector_size: 512
sd 1:0:0:0: [sdb] THECUS align 128M: sdp->tray_id: 2, dkp->capacity: 976748544, sector_size: 512
sd 1:0:0:0: [sdb] Write Protect is off
sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdb: sdb1 sdb2 sdb3
sd 1:0:0:0: [sdb] Attached SCSI disk
scsi 2:0:0:0: Direct-Access     ATA      ST3500320NS      SN05 PQ: 0 ANSI: 5
Thecus Tray: 1, sda
sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 2:0:0:0: [sda] THECUS  real size: sdp->tray_id: 1, dkp->capacity: 976773168, sector_size: 512
sd 2:0:0:0: [sda] THECUS align 128M: sdp->tray_id: 1, dkp->capacity: 976748544, sector_size: 512
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 2:0:0:0: [sda] 976773168 512-byte hardware sectors (500108 MB)
sd 2:0:0:0: [sda] THECUS  real size: sdp->tray_id: 1, dkp->capacity: 976773168, sector_size: 512
sd 2:0:0:0: [sda] THECUS align 128M: sdp->tray_id: 1, dkp->capacity: 976748544, sector_size: 512
sd 2:0:0:0: [sda] Write Protect is off
sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3
sd 2:0:0:0: [sda] Attached SCSI disk
input: thecus-kbd as /class/input/input0
rtc_cmos 00:04: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month
i2c /dev entries driver
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int32x1     64 MB/s
raid6: int32x2     76 MB/s
raid6: int32x4     73 MB/s
raid6: int32x8     71 MB/s
raid6: mmxx1      151 MB/s
raid6: mmxx2      214 MB/s
raid6: sse1x1     151 MB/s
raid6: sse1x2     220 MB/s
raid6: using algorithm sse1x2 (220 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
geode-aes: GEODE AES engine enabled.
u32 classifier
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
rtc_cmos 00:04: setting the system clock to 2008-12-10 10:31:55 (1228905115)
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sda2 ...
md:  adding sda2 ...
md: sda1 has different UUID to sda2
md:  adding sdb2 ...
md: sdb1 has different UUID to sda2
md:  adding sdc2 ...
md: sdc1 has different UUID to sda2
md: created md0
md: bind
md: bind
md: bind
md: running:
raid5: device sda2 operational as raid disk 0
raid5: device sdb2 operational as raid disk 1
raid5: device sdc2 operational as raid disk 2
raid5: allocated 3169kB for md0
raid5: raid level 5 set md0 active with 3 out of 3 devices, algorithm 2
RAID5 conf printout:
 --- rd:3 wd:3
 disk 0, o:1, dev:sda2
 disk 1, o:1, dev:sdb2
 disk 2, o:1, dev:sdc2
md: considering sda1 ...
md:  adding sda1 ...
md:  adding sdb1 ...
md:  adding sdc1 ...
md: created md1
md: bind
md: bind
md: bind
md: running:
raid1: raid set md1 active with 3 out of 4 mirrors
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 168k freed
Attaching PIC16F877
PIC_VER: 9
Attaching F75375
e1000: eth0: e1000_watchdog: NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
Filesystem "md0": Disabling barriers, not supported by the underlying device
XFS mounting filesystem md0
Ending clean XFS mount for filesystem: md0
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.28 [Flags: R/O MODULE].
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Setting latency timer of device 0000:00:0f.5 to 64
ehci_hcd 0000:00:0f.5: EHCI Host Controller
ehci_hcd 0000:00:0f.5: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0f.5: irq 10, io mem 0xefffd000
ehci_hcd 0000:00:0f.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 4 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Setting latency timer of device 0000:00:0f.4 to 64
ohci_hcd 0000:00:0f.4: OHCI Host Controller
ohci_hcd 0000:00:0f.4: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:0f.4: irq 10, io mem 0xefffe000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usblp
usbcore: registered new interface driver gspca
drivers/media/video/gspcav1-20071224/gspca_core.c: gspca driver 01.00.20 registered
zd1211 - http://zd1211.ath.cx/ - r85
Based on www.zydas.com.tw driver version 2.5.0.0
usbcore: registered new interface driver zd1211
ZD1211B - http://zd1211.ath.cx/ - r85
Based on www.zydas.com.tw driver version 2.5.0.0
usbcore: registered new interface driver zd1211b
Adding 2007992k swap on /dev/md1.  Priority:-1 extents:1 across:2007992k

Other

Please contribute...

Compatibility list

Harddrives

Alphabetical list of compatible harddrives. Please include the unique/exact model id.

Seagate 1,5TB ST31500341AS
Seagate 1,0TB ST31000520AS

RAM

Kingston KVR400X64SC3A/1G 1GB PC3200 CL3 200-Pin SODIMM
Corsair DDR 1Go PC3200 400Mhz SODIMM

Wireless

M3800 supports the following wireless USB adapters; which are based on ZyDAS ZD1211 chip. (from the manual)

3Com 3CRUSB10075 (Manufacture ID: 6891, Device ID: A727)
Zyxel G220USB (Manufacture ID: 0586, Device ID: 3401)
PCI GW-US54mini (Manufacture ID: 14EA, Device ID: AB13)

The following WLAN adapters are currently (firmware 1.00.02) supported. (from /app/bin/wlanchg.sh)

ZyDAS ZD1211 (This is the default card if none of the following are found by their PCI ids)
INPROCOMM IPN2220 (PCI id 17fe:2220)
Ralink RT2561/RT61 (PCI id 1814:030x)

The WLAN startup procedure can be found in /app/bin/wlanchg.sh.

Printers

Official printer compatibility list (2006-04-08) Note: This is the list for the N2100, there is no official list available for the M3800.

According to an unofficial Thecus users forum thread, the following printers are confirmed as supported:

Canon Pixima i4200
Epson Photo R800
Epson Stylus Color C880
HP Laserjet 1200
HP LaserJet 3050
OKI 5700C Color Laser w. duplex unit

Search

Navigation

SEARCH

TOOLBOX

LANGUAGES