Thecus N3200 Hardware
From NAS Website
Contents |
Default Hardware
CPU
- Freescale 8347 400Mhz
PCI
Other
- DDR SDRAM 256MB PC-3200
- FLASH RAM 16MB
- Supported HDD Size: 80/120/160/200/250/300/400/500/750/1000GB
- Serial port with active console on it fitted as 9 pin header behind fan cover on the back see [1]
Dmesg
Using MPC834x MDS machine description Linux version 2.6.21 (root@dev_222) (gcc version 3.4.3) #1 Mon Oct 1 21:48:21 C7 Found initrd at 0xcf389000:0xcffab211 Found legacy serial port 0 for /soc8349@e0000000/serial@4500 mem=e0004500, taddr=e0004500, irq=0, clk=266666664, speed=0 Found legacy serial port 1 for /soc8349@e0000000/serial@4600 mem=e0004600, taddr=e0004600, irq=0, clk=266666664, speed=0 Entering add_active_range(0, 0, 65536) 0 entries of 256 used Found MPC83xx PCI host bridge at 0x00000000e0008500. Firmware bus number: 0->0 Top of RAM: 0x10000000, Total RAM: 0x10000000 Memory hole size: 0MB Zone PFN ranges: DMA 0 -> 65536 Normal 65536 -> 65536 HighMem 65536 -> 65536 early_node_map[1] active PFN ranges 0: 0 -> 65536 On node 0 totalpages: 65536 DMA zone: 512 pages used for memmap DMA zone: 0 pages reserved DMA zone: 65024 pages, LIFO batch:15 Normal zone: 0 pages used for memmap HighMem zone: 0 pages used for memmap Built 1 zonelists. Total pages: 65024 Kernel command line: root=/dev/ram rw console=ttyS0,115200 ramdisk_size=32768 IPIC (128 IRQ sources) at fdefc700 PID hash table entries: 1024 (order: 10, 4096 bytes) time_init: decrementer frequency = 66.666666 MHz time_init: processor frequency = 399.999996 MHz Console: colour dummy device 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) High memory: 0k Memory: 243712k/262144k available (3156k kernel code, 18132k reserved, 96k data) Calibrating delay loop... 133.12 BogoMIPS (lpj=266240) Mount-cache hash table entries: 512 NET: Registered protocol family 16 PCI: Probing PCI hardware Registering ipic with sysfs... Generic PHY: Registered new driver SCSI subsystem initialized libata version 2.20 loaded. NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 4, 65536 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 12424k freed squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. SGI XFS with ACLs, large block numbers, no debug enabled io scheduler noop registered io scheduler anticipatory registered (default) io scheduler cfq registered Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xe0004500 (irq = 16) is a 16550A serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 17) is a 16550A RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize loop: loaded (max 8 devices) Gianfar MII Bus: probed eth0: Gianfar Ethernet Controller Version 1.4, 00:14:fd:11:2d:d6 eth0: MTU = 1500 (frame size=1514,truesize=1792) eth0: Running with NAPI enabled eth0: 256/256 RX/TX BD ring size eth0: Socket buffer recycling mode enabled eth1: Gianfar Ethernet Controller Version 1.4, 00:14:fd:11:2d:d7 eth1: MTU = 1500 (frame size=1514,truesize=1792) eth1: Running with NAPI enabled eth1: 256/256 RX/TX BD ring size eth1: Socket buffer recycling mode enabled SKB Handler initialized(max=64) Realtek RTL8211B: Registered new driver PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered sata_sil 0000:00:10.0: version 2.1 sata_sil 0000:00:10.0: Applying R_ERR on DMA activate FIS errata fix ata1: SATA max UDMA/100 cmd 0xd105c080 ctl 0xd105c08a bmdma 0xd105c000 irq 21 ata2: SATA max UDMA/100 cmd 0xd105c0c0 ctl 0xd105c0ca bmdma 0xd105c008 irq 21 ata3: SATA max UDMA/100 cmd 0xd105c280 ctl 0xd105c28a bmdma 0xd105c200 irq 21 ata4: SATA max UDMA/100 cmd 0xd105c2c0 ctl 0xd105c2ca bmdma 0xd105c208 irq 21 scsi0 : sata_sil ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata1.00: ATA-8: SAMSUNG HD501LJ, CR100-11, max UDMA7 ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata1.00: configured for UDMA/100 scsi1 : sata_sil ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata2.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7 ata2.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata2.00: configured for UDMA/100 scsi2 : sata_sil ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 310) ata3.00: ATA-8: SAMSUNG HD501LJ, CR100-12, max UDMA7 ata3.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32) ata3.00: configured for UDMA/100 scsi3 : sata_sil ata4: SATA link down (SStatus 0 SControl 310) scsi 0:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5 Thecus Tray: 1, sda SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPOA SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPOA sda: sda1 sda2 sda3 sd 0:0:0:0: Attached scsi disk sda scsi 1:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5 Thecus Tray: 2, sdb SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPOA SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPOA sdb: sdb1 sdb2 sdb3 sd 1:0:0:0: Attached scsi disk sdb scsi 2:0:0:0: Direct-Access ATA SAMSUNG HD501LJ CR10 PQ: 0 ANSI: 5 Thecus Tray: 3, sdc SCSI device sdc: 976773168 512-byte hdwr sectors (500108 MB) sdc: Write Protect is off sdc: Mode Sense: 00 3a 00 00 SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPOA SCSI device sdc: 976773168 512-byte hdwr sectors (500108 MB) sdc: Write Protect is off sdc: Mode Sense: 00 3a 00 00 SCSI device sdc: write cache: enabled, read cache: enabled, doesn't support DPOA sdc: sdc1 sdc2 sdc3 sd 2:0:0:0: Attached scsi disk sdc N3200 flash device: 1000000 at fe000000 Partition number 6 N3200 Flash Map Info: Found 1 x16 devices at 0x0 in 16-bit bank Intel/Sharp Extended Query Table at 0x0031 Using buffer write method cfi_cmdset_0001: Erase suspend on write enabled erase region 0: offset=0x0,size=0x20000,blocks=128 Creating 6 MTD partitions on "N3200 Flash Map Info": 0x00000000-0x00040000 : "u-boot" 0x00040000-0x00080000 : "u-boot config" 0x00080000-0x000a0000 : "kernel config" 0x000a0000-0x00180000 : "user" 0x00180000-0x00320000 : "kernel" 0x00320000-0x01000000 : "ramdisk" N3200 flash device initialized mice: PS/2 mouse device common for all mice i2c /dev entries driver rtc-rs5c372 1-0032: assuming rs5c372b rtc-rs5c372 1-0032: rs5c372b found, 24hr, driver version 0.4 rtc-rs5c372 1-0032: rtc core: registered rtc-rs5c372 as rtc0 md: linear personality registered for level -1 md: raid0 personality registered for level 0 md: raid1 personality registered for level 1 raid6: int32x1 33 MB/s raid6: int32x2 51 MB/s raid6: int32x4 73 MB/s raid6: int32x8 80 MB/s raid6: using algorithm int32x8 (80 MB/s) md: raid6 personality registered for level 6 md: raid5 personality registered for level 5 md: raid4 personality registered for level 4 raid5: measuring checksumming speed 8regs : 336.000 MB/sec 8regs_prefetch: 290.000 MB/sec 32regs : 364.000 MB/sec 32regs_prefetch: 353.000 MB/sec raid5: using function: 32regs (364.000 MB/sec) TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 md: Autodetecting RAID arrays. md: autorun ... md: considering sdc2 ... md: adding sdc2 ... md: sdc1 has different UUID to sdc2 md: adding sdb2 ... md: sdb1 has different UUID to sdc2 md: adding sda2 ... md: sda1 has different UUID to sdc2 md: created md0 md: bind<sda2> md: bind<sdb2> md: bind<sdc2> md: running: <sdc2><sdb2><sda2> raid5: device sdc2 operational as raid disk 2 raid5: device sdb2 operational as raid disk 1 raid5: device sda2 operational as raid disk 0 raid5: allocated 3170kB for md0 raid5: raid level 5 set md0 active with 3 out of 3 devices, algorithm 2 RAID5 conf printout: --- rd:3 wd:3 disk 0, o:1, dev:sda2 disk 1, o:1, dev:sdb2 disk 2, o:1, dev:sdc2 md: considering sdc1 ... md: adding sdc1 ... md: adding sdb1 ... md: adding sda1 ... md: created md1 md: bind<sda1> md: bind<sdb1> md: bind<sdc1> md: running: <sdc1><sdb1><sda1> raid1: raid set md1 active with 3 out of 4 mirrors md: ... autorun DONE. RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). Freeing unused kernel memory: 136k init Attaching PIC16F877 PIC_VER: 12 Attaching F75375 i2c_adapter i2c-1: Client creation failed at 0x2e (2) nf_conntrack version 0.5.0 (2048 buckets, 16384 max) ip_tables: (C) 2000-2006 Netfilter Core Team Filesystem "md0": Disabling barriers, not supported by the underlying device XFS mounting filesystem md0 PHY: e0024520:11 - Link is Up - 100/Full Ending clean XFS mount for filesystem: md0 Installing knfsd (copyright (C) 1996 okir@monad.swb.de). NTFS driver 2.1.28 [Flags: R/O MODULE]. usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1 fsl-ehci fsl-ehci.0: irq 39, io base 0xe0022000 fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usblp drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver Linux video capture interface: v2.00 usbcore: registered new interface driver gspca drivers/media/video/gspca-01.00.18-1/gspca_core.c: gspca driver 01.00.18 registd zd1211 - http://zd1211.ath.cx/ - r83 Based on www.zydas.com.tw driver version 2.5.0.0 usbcore: registered new interface driver zd1211 ZD1211B - http://zd1211.ath.cx/ - r83 Based on www.zydas.com.tw driver version 2.5.0.0 usbcore: registered new interface driver zd1211b Adding 2007992k swap on /dev/md1. Priority:-1 extents:1 across:2007992k
Compatibility list
Harddrives
Alphabetical list of compatible harddrives. Please include the unique/exact model id.
Official hard drive compatibility list (2007-11-15).